The PL2303GT is a low cost and high performance USB-to-RS232 Bridge Controller with built-in RS232 transceiver. The PL2303GT provides a convenient solution for connecting an RS-232 full-duplex asynchronous serial device to any Universal Serial Bus (USB) capable host. The PL2303GT highly compatible drivers could simulate the traditional COM port on most operating systems allowing the existing. The microUSB Programming Adaptor uUSB-PA5-II is a USB to Serial-TTL UART bridge converter which is simple, cost effective, very small and easy to use. It uses a mini-B type USB connector to connect to your PC. The uUSB-PA5-II is based on the SiLabs CP2104 USB to UART Bridge IC from Silicon Labs. To download the drivers, select the appropriate version of driver and supported operating system. The Driver Version must say 2.0.2.8 dated. PL2303 USB to UART Bridge Drivers Windows Download drivers @ / / / t.nl Windows 8 / 8.1. Once complete, Windows will confirm the successful installation of our driver as shown below, Figure 7. Device driver ft232 usb uart driver not installed successfully which was a nightmare literally. Usb uart communication with the available version. The ftdi ft231x usb2.0 full speed ic offers a compact bridge to basic uart interfaces, with low power consumption 8ma, and is capable of operating up to 3mbaud.
CP2102 is a USB to UART IC from Silicon Labs. It is my favourite converter IC and I have been using USB to RS232 module and USB to TLL modules based on CP2102 for couple of years without any issues. CP2102 is a cheaper alternative to the costlier ftdi IC (ft232) but cp2102 is a bit difficult to solder as it comes in QFN-28 package and is very small (just 5mmx5mm) in size. The main advantage of CP2102 is that no extra external components are required.
CP2102 IC is used in lot of Arduino UNO Clones, arduino Nano, Node MUC and even in ESP32 Development boards. In this tutorial I will provide you with step by step process to install CP2102 USB Driver in windows.
You can download CP2102 driver from below
- CP2102 USB Driver for Windows XP, 7, 8, 8.1 & Windows 10
Step by Step Installation of CP2102 Drivers
Initially connect your hardware having CP2102 USB to Serial IC to your PC. In the device manager it will show “CP2102 USB to UART Bridge Controller” (as shown in below figure) which means that your PC has detected the drivers but please note the “!” sign which indicated cp2102 drivers have not been installed.
Now extract the “CP210x_Windows_Drivers” in a folder and in that you will find applications named “CP210xVCPInstaller_x64” & “CP210xVCPInstaller_x86”. If your system is 64 bit then run “CP210xVCPInstaller_x64.exe” application and if it is 32 bit then run “CP210xVCPInstaller_x86” application.
Download Gt System Usb To Uart Bridge (com4) Drivers
Once you run your application it will show you the welcome screen click “Next” on the screen. Then the license Agreement screen is shown select “I agree” and then on “Next”.
Just relax now the CP2102 drivers will start installing…..and within few seconds completed screen will be displayed.
Once installed it will show driver successfully installed. Now go again back to device manager and there you will see that the driver has been successfully been installed and a com port has been allotted. In below image you can see that “com4” has been allotted for cp2102 IC in my laptop.
Drivers for the CP2102 have now been installed successfully. I have tested this drivers and installation process in Windows XP, windows 7. Will test is soon on Windows 8 & windows 10.
You can see in above image that Port Number 4 has been allocated to this IC. If you want you can even change the virtual com port number from Device Manager.
Download Gt System Usb To Uart Bridge (com4) Driver Windows 7
For latest CP2102 drivers and for drivers for MAC, Linux and for Android OS please check this link.
Download Gt System Usb To Uart Bridge (com4) Driver Updater